Drill template for a project box, true size, any face
Free, in your browser, nothing uploaded: pick a Hammond 1590 box or type your own, place the jacks, pots, footswitch and LEDs on any face, and print a true-size template that wraps the box, with a ruler to check the scale and a drill list. Or take the holes as an SVG or a DXF.
Faster with the free Chrome extension: right-click any picture on a website and send it straight to the drill template maker. Add to Chrome · what it does
Extension installed. Right-click any picture on a website and choose Makerfern → Open this picture in… to bring it here.
Holes where you planned them
Drilling a pedal or project box is mostly marking out: measuring from edges that are not quite square, on faces that taper, with a pot that has to clear a footswitch inside. This tool lays the whole box out flat, puts each hole where its numbers say, warns you when a part will hit a wall, a lid screw post or another part, and prints it at true size so you can tape it on and centre punch.
What you get
- A drill template PDF: the box unfolded on Letter or A4, every hole with a centre cross and a number, centre lines to line it up, a 100 mm and a 4 inch bar to check the print.
- A drill list: every hole by face, its size in millimetres and inches, and where it is.
- An SVG and a DXF, of the whole box or one face, for a laser cutter, a CNC or your CAD program.
How to use it
- Pick the box, or type your own box's outside size.
- Add each part, choose its face, and type where it goes from the centre lines. Or try the sample pedal.
- Fix anything marked Fix, and look at anything marked Check.
- Print at 100%, measure the 100 mm bar, cut, fold, tape and centre punch.
- Drill a small pilot hole first, then open it up to size with a step bit.
What it does not do
- It does not know your exact parts: the hole sizes are a start, and parts need room inside that only you can check.
- It does not lay out a circuit board or check that the circuit fits.
- It does not draw the lid or the rounded corners of the box: line the template up by its centre lines.
Questions
Which boxes are in the list?
The Hammond 1590 die-cast boxes guitar pedal builders use most: the 1590A (92.6 x 38.5 x 31 mm), 1590B (112.4 x 60.5 x 31 mm), 1590N1, the 125B size (121.2 x 65.5 x 39.8 mm), 1590BB (119.5 x 94 x 34 mm), 1590XX (145.2 x 121.2 x 39.3 mm) and 1590DD (188 x 120 x 37 mm). The sizes are read from Hammond's own drawings: the outside at the open rim, the height with the lid on, the inside, and where the lid screw posts are. Many sellers sell boxes of these sizes under their own names; measure yours, and if it differs, choose Your own box and type its size.
What size hole does each part need?
The list starts each part at the hole builders usually drill for its mounting thread: 7 mm for a 16 mm pot, 9.5 mm for an open-frame 1/4 inch jack and 11 mm for an enclosed one, 12 mm for a 3PDT footswitch, 8 mm for a round 2.1 mm DC jack, 6.4 mm for a mini toggle, 3.2 mm for a 3 mm LED and 6.35 mm for a 5 mm LED bezel. Parts from different makers differ, so measure the thread on yours or read its datasheet, and type the hole in. Drill a test hole in scrap first if you can.
How do I line the template up on the box?
Print the PDF at 100% and measure the 100 mm bar first. Cut the unfolded box out on its solid lines and fold it on the dashed ones, so it wraps the box. Line the long dash-dot centre lines up with the middle of each face, tape it down, and centre punch each cross. The sides of a die-cast box taper a little, so its faces are a fraction smaller than the size at the rim: lining up by the centre lines keeps every hole where you put it.
Where do the positions start from?
From the face's centre lines. On the top face, a part is so many millimetres across from the middle (right is plus) and along it (toward the top end is plus). On the ends and sides it is along the edge from the middle, and down from the top face, so a jack at 15 mm down sits 15 mm below the top face's edge. You can also select a part and tap the drawing to move it there.
What do the warnings mean?
A hole that runs off its face, or into another hole, has to be moved. A warning means the hole fits but the part may not: its nut or body reaches an inside wall, a lid screw post, the lid, or the inside of the top face, or a pot's 16 mm body meets another part. Inside a box, jacks and pots also need room behind them; the drawing shows each pot's body as a faint circle.
Can I use it with a laser cutter or a CNC?
Yes. Download the SVG or the DXF, of the whole box unfolded or of one face. Both are in millimetres at true size, with the holes on their own layer. One face alone has its origin at the centre of the face (the top face) or at the middle of the edge it shares with the top face (an end or a side), so you can zero your machine there.
Is anything uploaded?
No. The template, the drill list and the cut files are made in your browser.