New Makerfern for Chrome: right-click any picture on the web to make a cut file, coloring page or stencil from it. Add to Chrome, free

Tumbler and mug wrap template maker

Enter the cup's measurements and get a tumbler or mug template at real size, straight or tapered, free and with nothing uploaded. Drop your design and it is warped to the curve, ready to print at 300 dpi.

Updated : If your design fits on one sheet of your paper, the design PDF now puts it whole on that sheet instead of cutting it in two. What's new

Stays on this computer · no signup · no watermark

Faster with the free Chrome extension: right-click any picture on a website and send it straight to the tumbler template maker. Add to Chrome · what it does

Why a tapered tumbler needs a curved template

Measure round the top of a tapered tumbler and round the bottom and the numbers differ. Unrolled, that shape is a slice of a ring: the top edge a long arc, the bottom a shorter one. A rectangle printed and wrapped round it climbs on one side, and the two ends meet at an angle with a wedge of bare cup between them. The fix is to print the design on the curve, and that is what this tool draws, with the arc worked out from your three measurements.

What you get

  • A starting cup: 20 oz skinny, 20 and 30 oz tapered, 40 oz with a handle, 11 and 15 oz mugs, 16 oz glass can. Typical sizes, to measure against yours.
  • The template at real size: a print-ready PDF, a 300 dpi PNG and a layered SVG, with the cut line, the dashed edge of the print area, centre and quarter marks, TOP, the seam or handle gap and a one-inch square.
  • Your design warped to the curve: stretched or cropped to fill the wrap, or placed at its true shape at the size and spot you choose. On a full wrap the bleed carries the design on past the seam.
  • Your design on the cup: turn the cup to the front, the sides or the seam and see where the design, the seam and a handle gap land, then download a mockup PNG for a listing (transparent, white or grey, up to 3000 px, no watermark).
  • The size to design at in pixels, and how sharp your file will print, with a warning when it will look soft.
  • Which sheet it fits inside your printer's margins, and a PDF split over two sheets when it doesn't fit one.

How to measure, and the traps, are in how to make a tapered tumbler template that fits.

Questions

Do I need to warp my design for a tapered tumbler?

Yes. A tapered cup is a cone with its tip cut off, and a cone unrolls to part of a ring, not a rectangle. A rectangular design wrapped round it tilts, and the ends meet in a V-shaped gap. Warping the design to the curve puts the top edge of the artwork on the top edge of the cup all the way round. Drop your design on the tool and it does the warp for you.

How do I measure my tumbler?

Measure straight across the cup where the top of the design will sit (the diameter), and again where the design ends. Or wrap a strip of paper round the cup at each line, mark where it overlaps and measure the strip (the circumference), and choose that option: it is the more accurate of the two. For the height, measure along the side of the cup between those two lines, or straight up with a ruler and choose that option. Measure the actual cup: sizes differ between brands even when the ounces match.

Should I mirror the design for sublimation?

It depends on your printer's software, not on the cup. Many sublimation setups mirror automatically, and mirroring twice prints the design backwards. Check what your printer does with one small test before a whole run; the mirror switch here is off unless you turn it on.

What is the bleed for?

Extra design past the edges, so a tiny misalignment in wrapping or pressing does not leave a bare line where the ends meet or at the rim. On a full wrap the bleed past each end carries on with the other end of your design, so the join matches; at the rim and the base it repeats the edge of your artwork outwards. The template marks the edge of the print area with a dashed line.

What size should I make my tumbler design?

The tool tells you, in pixels at 300 dpi, once the cup is measured: the print area's width half-way up by its height, before bleed. Pick the nearest cup in the list to start (the sizes there are typical, not any maker's spec, so measure yours and correct them). If your design is a different shape, choose to fill the wrap and crop, or place it at its true shape, rather than stretch it. The tool also shows how many dpi your file will print at and warns when it will look soft.

How do I print it at the right size?

Download the print-ready PDF for your paper, print it at 100% ("Actual size"), not "Fit to page", and measure the one-inch square or the two-inch bar. The PDF keeps the template inside your printer's margins and turns it the way it fits; when it is too big for the sheet it is split over two or more sheets that overlap by half an inch, with a dashed line to join them on.

Is the picture of the cup what my print will look like?

It shows where your design lands, not how the colours print. The cup view reads the same pixels the print file is made of and wraps them on a cone drawn from your measurements, so a logo that sits too far round, a design that crosses the seam or a wedge-shaped gap on a tapered cup shows up before you spend a blank. It is a preview, not a photo: the cup is a plain white blank without a handle, lid or finish, and the shading is a simple studio light. Real sublimation or DTF colour depends on your blank, your ink and your press, so test a small print before a run. The mockup PNG is the same picture on a transparent, white or grey background, free and without a watermark; it is never mirrored, because it shows the finished cup.

Does it make mug templates too?

Yes. A mug is usually a straight cylinder, so set the top and bottom to the same measurement and it becomes a plain rectangle. Set the coverage below 100% to leave room for the handle, and place a logo in the middle or a quarter round either side of it.

Can I sell what I make with it?

Yes. Everything Makerfern makes is yours to use and sell, free or Pro, as long as you have the right to use what you start from: your own photos and drawings, or pictures whose license allows it; somebody else's art or characters only with their permission. Makerfern adds no watermark and takes no rights in your file. One Pro covers every tool: there is no per-tool plan.